Introducing the first ultra-light Long Range 4inch for every terrain from iFlight. Newest iFlight SucceX hardware onboard coupled with the XING 1404 motors in 3000kv. Slow cruising or speedy action, there's something for every taste. Get flight times above 15min using at least 4S 850mAh packs. Go crazy and strap a Li-On 4S pack on and go even further, depending on capacity and weight! GPS Rescue ready for easy recovery in case of signal loss, or even if you've been surfing those mountains and suddenly can't find the way back home... Betaflight OSD pre-setup GPS elements will show you the way!
CaddX Nebula camera with Vista Air Unit for fantastic imagery and performance in digital HD.
Outstanding digital FPV experience in 720p directly on your goggles. Custom iFlight 150mm LR antenna for best signal coverage even at long distances.
- Sub 250g long-range quad
- XING 1404 3000KV Ultralight motors
- GPS pre-installed for more safety at distance
- SucceX-E mini F4 +35A 4in1 ESC Flystack
- Naked for GoPro ready
- 360° TPU protection, Nebula cam protection, and antenna mounts
- Caddx Nebula Digital HD System
- Wheelbase: 178mm
- Main body dimension: 136.8*114.8mm
- Bottom to top distance: 28mm
- Arm thickness: 4mm
- Bottom plate thickness: 4mm
- Top plate thickness: 2mm
- TPU Camera plate thickness: 2mm
- FC: 25.5*25.5mm/20*20mm/16*16mm
- FPV Cam: 19mm Micro / 20mm
SucceX-E mini F4
- MCU: 168MHz STM32F405
- Gyro: MPU6000
- Blackbox: 8MB
- Betaflight OSD: YES
- BEC: 5V 2.5A
- Uarts: 5
- ESC Telemetry: yes
- INA Pad: nuart2
- Input voltage: 2-6S
- Firmware: BETAFLIGHTF4
- Size: 25*25mm /20*20mm φ3 mounting
- Mounting hole: 20*20mm，φ3mm
- Size: 25*25mm
- Weight: 4g
NOTE: F.PORT protocol RX input support, telemetry not supported.
ESC // SucceX-E mini 35A
- MCU: BB21 F16G
- Capacitance: 470uF/50V
- Current Sensor: Yes
- Input: 2-6S LIPO
- Constant: 35A / Burst: 40A
- BEC: No
- Supports up to Dshot600, Proshot, Oneshot, Multishot
- Target: G-H-30
- Weight: 6.9g
- Mounting pattern: 20*20, φ3mm with Grommets φ2mm
- Dimensions: 31*30mm (including the power pads)
Prebuilt and indoor tested FPV Racing Drone
Additional Suggested Parts (not included)
- 4S 850mAh / 4S 1100mAh
- TPU Naked GoPro Mount
- DJI HD FPV Goggles
- Radio Controller
- DJI Remote Controller (Mode 1/ Mode 2)
PRE-TUNED & PRE-SETUP:
- Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!
- To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"
- Angle-Mode (self-balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!
- Please check our linked article on "How to disable Angle-Mode, activate Acr0-Mode"
- GPS Rescue is OFF by default to prevent from unwanted or unexpected drone behaviour.
- Please check our linked article on "GPS Rescue Mode // Setup"
1x iFlight Chimera 4 HD 4" BNF
1x Caddx Nebula Digital HD System
2x Albatross LHCP ipex 160mm Antennas
1x Nazgul 4030 Prop Set
1x Gemfan 4024 Prop Set
2x 15*15mm Microfiber PU Leather Battery Strap
We Also Recommend
Pyrodrone CNC Machined Folding Hall Gimbal Set for TBS Tango 2 and Mambo