iFlight Beast F7 45A AIO Flight Controller V1.2
What if you could get the combined MCU speed and ESC power of a big stack, but carefully arranged on a 25x25 whoop size board? That would be crazy right? Well, we just did it...
This is our new iFlight BEAST series AIO FCs for your ultimate build. A future proof all-in-one FC to step up the game and make some more room for future flight firmware development like Betaflight, Emuflight etc. Lightweight, minimum size, minimum work.This could only be achieved by using BGA chipsets instead of ordinary QFP (big size) MCUs and ultra powerful Mosfets for almost any build. Solder your motor wires on and let's go! DJI Plug&Play plug and so many UARTs most people wouldn't even use em' all. Compatible to digital and analog FPV, onboard Barometer for possible long range flights and much more. Unleash the beast!
Features:
- Vista digital system Plug-and-Play (VBAT passthrough)
- MCU: BGA-STM32F745, 216MHz
- OSD: AT7456E
- Gyro: MPU6000
- Blackbox: 16MB
- Onboard Flash
- BEC output: 5V 2.5A
- Barometer: DPS310
Changelog:
- V1.0 - V1.1: Due to some global supply issues, the Barometer and Flash component was updated as well as some circuit improvements implemented.
- Before BMP280 changed to DPS310
- Before 8MB Flash changed to 16MB Flash
*Barometer can only be used with Betaflight 4.3.0 and above!
Safety Reminder:
The DJI plug&play port has no voltage regulator (BEC) and is passing through VBAT. The Caddx Vista goes up to 26.4V (6S), the DJI Air Unit goes up to 17.6V (4S). Make sure not to plug-in your DJI Air Unit directly when you're flying 6S, because this would fry it! BEC to add for your 6S build is recommended.
Small motor 4S builds should usually need an additional capacitor of at least 16V/220uF, for 6S go up to 35V or even 50V. Bigger motors have a bigger current draw, higher voltage spikes, and more serious back EMF (motor braking, works like a generator). Make sure to add big enough or even bigger low ESR capacitors on the AIO battery pad or on your battery lead the more aggressive motors you fly. There's a choice of capacitors in the package, but it's never a bad idea to make sure to protect your board. Smaller boards have less capacitance which has to be covered with external capacitors, there's no way around it.
Specifications:
Flight Controller:
- MCU: BGA-STM32F745
- Gyro: MPU6000
- Blackbox: 16MB Onboard Flash
- BEC output: 5V 2.5A
- Barometer: DPS310
- Connector: Micro-USB
- OSD: IFLIGHT OSD (AT745E）
- FC Firmware：IFLIGHT_F745_AIO 4.2.4
- Mounting pattern: 25.5*25.5mm φ3mm
- Dimensions: 32.5*32.5mm
- Weight: 8.5g
ESC // 45A 2-6S:
- Uarts: 5
- Current Sensor: Yes
- Input: 2-6S
- LIPO Current scale: 100
- Constant: 45A / Burst: 50A
- BLHeli: BLHeli-S
- Telemetry: no
- ESC Firmware: BlheliS G-H-30 BLS 16.7
- Mounting pattern: 25.5*25.5mm/Φ3mm
- Dimensions: 32.5*32.5mm
Includes:
1x iFlight Beast F7 45A AIO Flight Controller V1.2
1x Capacitor 470uF/16V
1x Capacitor 470uF/35V
1x XT60 16AWG cable 100mm
1x XT30U 18AWG cable 70mm
1x 14AWG Silicone Cable Red 100mm
1x 14AWG Silicone Cable Black 100mm
1x 1.0-7P cable 50mm-28mm
1x 1.0-7P cable 50mm
4x M2 silicon grommets
8x M2*12mm screws
8x M2 Transparent Nylon Nut
8x 0.8mm black Heat shrink tube 10mm
